UISS

UISS setting up with Interface


JA0CAW built the guide to set up UISS using only Soundcard (Non-TNC). [16Nov2007]

UISS setting up #1
Interface to PC #2
AGWPE availale  #3




 
UISS program uses after starting AGWPE, AGW Packet Engine.

AGWPE, AGWMonitor available
http://www.sv2agw.com/downloads/

AGWPE, AGWMonitor guide
http://www.ne.jp/asahi/hamradio/je9pel/agwpinfo.htm

UISS available
http://users.belgacom.net/hamradio/uiss.htm

UISS easy guide
http://users.belgacom.net/hamradio/uisslinks.htm

UISS guide, standard version
http://ja0caw-je0mzi.mo-blog.jp/syumi/files/UISS-pdf.pdf

UISS guide, added tone encoder version
http://ja0caw-je0mzi.mo-blog.jp/syumi/files/Satellite-1.pdf

UISS guide, added interface circuit version
http://ja0caw-je0mzi.mo-blog.jp/syumi/files/UISS-SET.pdf

Sound Card Packet
http://www.soundcardpacket.org/

 



Supplement by JE9PEL as follows.



It may be put a Resistor between Capacitor and DATA_IN so as not to have trouble.






     

Interface between PC and RIG

(1) Red: PC earphone terminal for 1k2/9k6 uplink
    White: PC microphone terminal for 1k2/9k6 downlink

(2) White: Transistor(2SC1815) + Diode(1S1588)
    Yellow: Transformer ST71(600:600) + Capacitor(10uF)

(3) Switching connector for 1k2/9k6
(4) Connector between PC_COM2(USB) and RIG_PTT
(5) Inside of this switching connector

(6) Yellow: RIG microphone terminal for 1k2 uplink
    White: RIG earphone terminal for 1k2 downlink
    Connect directly to the inside of the radio by
    replacing the switching connector(3) for 9k6.
    (Connectable to 9k6 data terminal of RIG.)


AGWPE setting page
http://www.soundcardpacket.org/

If you can't decode even though strong signal,
then change the value of Soundcard Clock to 2 in

  AGWPE - Properties - Port - TNC Setup - SoundCard
           - Options - Adjust The Soundcard Clock


UISS uplink success!




  Fm JE9PEL To APRS Via RS0ISS-4* <UI pid=F0 Len=43 >[14:40:35] =3523.05N/13936.61E-Yokohama Japan {UISS51}
  Fm JE9PEL To APRS Via RS0ISS-4* <UI pid=F0 Len=19 >[14:42:53] Hello all from UISS
  Fm JE9PEL To APRS Via RS0ISS-4* <UI pid=F0 Len=19 >[14:43:23] UISS uplink success
  Fm JE9PEL To APRS Via RS0ISS-4* <UI pid=F0 Len=43 >[14:43:41] =3523.05N/13936.61E-Yokohama Japan {UISS51}
  Fm JE9PEL To APRS Via RS0ISS-4* <UI pid=F0 Len=52 >[14:43:49] :EMAIL    :ei7m-wkt@asahi-net.or.jp /SatSE Test UISS
  Fm JE9PEL To APRS Via RS0ISS-4* <UI pid=F0 Len=19 >[14:44:08] UISS uplink success
  Fm JE9PEL To APRS Via RS0ISS-4* <UI pid=F0 Len=18 >[14:44:59] JA6PL JE4SMQ Hello
  Fm JE9PEL To APRS Via RS0ISS-4* <UI pid=F0 Len=9  >[14:45:50] from UISS

 
AGWPE, AWGMonitor available:
http://www.sv2agw.com/downloads/

AGWPE, AWGMonitor explanation:
http://www.soundcardpacket.org/2agwget.htm

UISS available:
http://users.belgacom.net/hamradio/uiss.htm

UISS guide:
http://users.belgacom.net/hamradio/uisslinks.htm