Go to WiSP update
Go to how to install WiSP
Go to how to UNinstall WiSP ============ WiSP update ============ http://www.amsat.org/amsat/ftpsoft.html#win-wisp http://www.amsat.org/amsat/ftp/software/win32/wisp/ http://www.amsat-warenvertrieb.de/english.htm http://www.ne.jp/asahi/hamradio/je9pel/wispinfo.htm Subject: [amsat-bb] WiSP Update - GSC 2.02 From: Roy Welch [rdwelch (at) swbell.net] To: amsat-bb (at) amsat.org Date: Wed, 05 Jan 2000 02:03:44 +0000 Hi Guys, Chris has asked me to upload an update for the WiSP32 GSC module. This update only corrects the problem with year 2000 keps updating. There may be an additional update of GSC soon to correct some other items. The file will be put on KO-25, UO-22 and is already on the AMSAT ftp site at http://www.amsat.org/amsat/ftp/software/win32/wisp/ The file will be GSC202.ZIP. It has also been incorporated in the WiSP3213.EXE file. As always retain your old GSC until you are satisfied with the update. It seems to be working OK here. 73, Roy -- W0SL Subject: [amsat-bb] GSC Update 2.03 From: Roy Welch [rdwelch (at) swbell.net] To: amsat-bb (at) amsat.org Date: Fri, 07 Jan 2000 15:55:01 +0000 Hi Guys, Chris has released GSC 2.03 which seems to have corrected the Track Box problem. It has been tested at a site where the Track Box is being used and where the problem was experienced. This version corrected it. It will be uploaded to KO-25, UO-22 and the AMSAT ftp site at http://www.amsat.org/amsat/ftp/software/win32/wisp/ The file will be GSC203.zip. Chris has burned some midnight oil getting this update out. There are a few more items you will find in this version. Here's the additions list -: 1. Tx Port: In TNC Setup the item 'Tx Port' has been added. This is only used for TNCs with multiple modems such as the Symek TNC3S. It switches the the PTT control between the two modems. In general, this should be set to 0 for single modem TNCs. It will only be used when a new version of MSPE is released in the next couple of weeks. 2. Rotator Ports: COM1 to COM12 can be used for the rotator port. 3. DDE Interface: The current MA number has been added to the end of the DDE string. 4. There is an additional item for Satgates on the Satgate Tab of the Satellite Setup. 5. The Flip Mode seems to work now. I just checked it out last night and it went into the flip mode on a pass. This was not one of the items in Chris'list of fixes for this version, but it may be fixed now anyway. Try it out. As usual keep your old version until you are satisfied with the perfor_ mance of this one. -- 73, Roy Internet: w0sl (at) amsat.org Home Page: http://home.swbell.net/rdwelch/ ------------------------------------------ ==================== How to install WiSP ==================== 1. Make 'wisp' subdirectory such as C:/wisp, or C:/wisp32 2. Copy 'wisp32.zip' into C:/wisp and extract them. Note : The WISP32xx.EXE file is the current format and is self extracting. Current version is now WiSP3215. http://www.amsat.org/amsat/ftp/software/win32/wisp/ 3. Move into another directory the next two files. bwcc.dll --> C:/Windows/System wisp.hlp --> C:/Windows Note : No need to do this. The Install program will move necessary files to the correct directory. 4. Run 'setup.exe' on Windows95. 5. Setup in 'WiSP Setup'. (1) WiSP Directory : C:/wisp (2) Check 'I want to register'. (3) Input your Callsign. (4) Input your Registration Number. (5) Click 'OK' button each the popup messages, but not delete PIF files. 6. Exit Windows95 and add the next words in 'autoexec.bat'. set tz=jst-9 share /f:4096 /l:75 path = c:\wisp And run again 'gsc.exe'. You don't need to write these last two line commands in 'autoexec.bat'. But you must write in 'tz=est+5 ' if you live in N.Y. Japan Standard Time (JST) is 9 hours fast from UTC(GMT), so 'tz=jst-9'. Eastern Standard Time (EST) is 5 hours slow from UTC(GMT) ? Note : The above is not required with WiSP32. WiSP32 takes the time zone from the Windows Time Zone setting, not the TZ parameter. Share is nor required and the path is automatically set in the Setup program. 7. In the popup 'WiSP Unregistered Copy', input again your Registration Number and click 'Register'. After the next run, it is not shown this message. 8. GSC - Setup - General Setup - WiSP Program Directory - C:/wisp , and Display time in: Local and GSC - Setup - Select Font 9. GSC - Setup - Station Setup - (ex)Latitude 35.4 N Longitude 139.6 E 10. GSC - Setup - Edit MSPE equations - In the case of a message [Not found C:/wisp/MSPE equations.TXT], Click 'Yes' 11. NOTEPAD File - Open - Mspeeq~1.txt - Open - File - Save attached new file name - MSPE Equations.TXT - Save In the message [C:/wisp/MSPE Equations.TXT Overwrite?], Click 'Yes' Note : No need to do this any longer. The AMSAT distributed versions will extract this file with the correct name. 12. GSC - Setup - Edit View-Dir equations In the case of a message [Not found C:/wisp/View-Dir equations.TXT], Click 'Yes' 13. NOTEPAD File - Open - View-d~1.txt - Open - Remove [ZL2TPO] and add [your callsign] Remove destination="ZL" and add destination="your callsign" Save attached new file name - View-Dir Equations.TXT - Save In the message [C:/wisp/View-Dir Equations.TXT Overwrite?], Click 'Yes' Note : No need to do this any longer. The AMSAT distributed versions will extract this file with the correct name. But, the part of [your callsign] must be rewritten. 14. GSC - Setup - MSPE Setup - Sat Change - Automatic - OK 15. GSC - View-Dir Setup - Maximum messages to load - 900 - OK 16. GSC - MsgMaker Setup - Message expiry time - 7 - OK Note : Do not set this to 7. The maximum value used is 4 and this should only be used for large files that will take a while to download. Normally this should be left set to 2 to keep the file space minimized on the satellite. Even at that, the file will not be deleted at the expiration time. At that time it is available to be deleted if the file space is required for new messages. 17. GSC - ProcMail Setup - Automatic Keps file updating - Check 'Update with any keps file'. 18. GSC - Database - Update Satellite Database - (ex)20107kep.txt - OK Then it show [Not Updated]. But when the new keps, then it show [Updated]. 19. GSC - Setup - Satellite Setup - Satellites - New - General - Name KO-25 Satellite Type PacSat Broadcast Callsign HL02-11 BBS Callsign HL02-12 Priority 1 (Order) Frequencies (confirm) TNC Settings (confirm) Directries (confirm) MSPE Settings (confirm) Because the box of 'Scheduling - Pragram' is the blanks when you chose 'Analogue' in 'Satellite Type', you must add 'C:/wisp/MSPE.EXE %S'. GSC - Setup - Satellite Setup - Satellites - Edit - MSPE Settings, check below. Update Keps from broadcast Uploading enabled Log KISS frames Log Telemetry frames Grab all heard files Brock ALL BBS files Acknowledge receipt Load View-Dir at start of pass Close View-Dir at end of pass etc. Note : These are the settings when you want to validate these between the path of the satellite. Please set it if necessary. In addition, the setting of MSPE Settings do the same setting once again because it do not become effective once. Satellite Setup - Satellites - Edit - MSPE Settings And click 'OK - Close', then GSC schedule the satellite. 20. Other Satellites 'Broadcast Callsign, BBS Callsign'. +------------------------------------------------------------------------------------------+ : Sats , AO-16 LO-19 UO-22 KO-23 KO-25 IO-26 TO-31 UO-36 : +------------------------------------------------------------------------------------------+ : Broad, PACSAT-11 LUSAT-11 UOSAT5-11 HL01-11 HL02-11 ITMSAT-11 TMSAT1-11 UO121-11 : : BBS , PACSAT-12 LUSAT-12 UOSAT5-12 HL01-12 HL02-12 ITMSAT-12 TMSAT1-12 UO121-12 : +------------------------------------------------------------------------------------------+ http://www.ne.jp/asahi/hamradio/je9pel/satslist.htm 21. GSC - Tracking - Track - Satellites - KO-25 - ADD - OK GSC - Tracking - Graphic Track - Tracking - Select Satellite - KO-25 - OK GSC - Setup - Select Map Font 22. Close GSC once last, and open again GSC so that WiSP.KEP and WiSP Schedule.DAT becomes the update date. After doing so it, 'GSC - Tracking - Redo Schedule'. WiSP32 all settings http://www.ne.jp/asahi/hamradio/je9pel/wispsett.htm [Supplement] ---------------------------------------------------------------------------- Subject: [jamsat-amsat-bb:31418] Re: WiSP Config Tutorial From: Roy Welch [rdwelch (at) swbell.net] To: PAT McGRATH [patricio (at) cyberg8t.com] Cc: Fernando Mederos [fmederos (at) adinet.com.uy], amsat-bb (at) amsat.org, Astronautic Technology [tiung (at) po.jaring.my] Date: Tue, 04 Apr 2000 19:21:16 +0000 PAT McGRATH wrote: > > I found the following of great help. > http://www.ne.jp/asahi/hamradio/je9pel/wispinse.txt > > ---- There some things in that document that are no longer correct. -- 73, Roy ------------------------- In How to install WiSP32 ------------------------- -----------SNIP-------------- 2. Copy 'wisp32.zip' into C:/wisp and extract them. The WISP32xx.EXE file is the current format and is self extracting. -----------SNIP-------------- 3. Move into another directory the next two files. bwcc.dll --> C:/Windows/System wisp.hlp --> C:/Windows No need to do this. The Install program will move necessary files to the correct directory. -------SNIP------- 6. Exit Windows95 and add the next words in 'autoexec.bat'. set tz=jst-9 share /f:4096 /l:75 path = c:\wisp The above is not required with WiSP32. WiSP32 takes the time zone from the Windows Time Zone setting, not the TZ parameter. Share is nor required and the path is automatically set in the Setup program. ---------SNIP------------- 11. NOTEPAD File - Open - Mspeeq~1.txt - Open - File - Save attached new file name - MSPE Equations.TXT - Save In the message [C:/wisp/MSPE Equations.TXT Overwrite?], Click 'Yes' No need to do this any longer. The AMSAT distributed versions will extract this file with the correct name. --------SNIP--------- 13. NOTEPAD File - Open - View-d~1.txt - Open - Remove [ZL2TPO] and add [your callsign] Remove destination="ZL" and add destination="your callsign" Save attached new file name - View-Dir Equations.TXT - Save No need to do this any longer. The AMSAT distributed versions will extract this file with the correct name. ------------SNIP------------ 16. GSC - MsgMaker Setup - Message expiry time - 7 - OK Do not set this to 7. The maximum value used is 4 and this should only be used for large files that will take a while to download. Normally this should be left set to 2 to keep the file space minimized on the satellite. Even at that, the file will not be deleted at the expiration time. At that time it is available to be deleted if the file space is required for new messages. ----------SNIP----------- 19. GSC - Setup - Satellite Setup - Satellites Acknowledge receipt Only used by UO-22 Load View-Dir at start of pass Close View-Dir at end of pass etc. Only if you want this window open all during the pass. You can leave it unloaded and call it up any time you wish. ---------------------------------------------------------------------------- ==================================== Complete deletion and REinstall WiSP ==================================== 1. Delete all, C:/wisp directory with all wisp32 files. 2. Run regedit.exe such as, Start - Run with the file name - Browser - - C:\Windows - Regedit.exe - Open - OK - - HKEY_LOCAL_MACHINE - SOFTWARE - WISP - - Edit - Delete Similarly, delete all relative wisp32 items. 3. Re-create a new directory, C:/wisp directory and extract new wisp32. 4. Run, setup.exe as the above 'How to install WiSP32'. G6LVB / Howard Long wrote at 28 Jun 2002: o Shut down Wisp o Rename the Wisp.kep file to something else (just in case) o Restart Wisp. o For each satellite which was previously scheduled, you will get an error "GSC cannot find satellite xx-xx in the keplarian database....". OK each message. o Re-import the keps (Database -> Update Satellite Database) o Shutdown Wisp o Restart Wisp o Tracking -> Redo Schedule JE9PEL wrote How to reset WiSP.KEP: 1. Delete 'C:\wisp\WiSP Schedule.DAT' and 'C:\wisp\WiSP.KEP' 2. Run GSC.EXE 3. Then you will get an error message: 'GSC cannot find satellite ... in the keplerrian database' OK each messages. 4. GSC - Database - Update Satellite Database and import the right TLE file. 5. GSC - Setup - Satellite Setup - (satellite) - Edit - OK Do it each satellites. 6. GSC - Tracking - Redo Schedule