Attention Please Mobile Office MebiusNote PJ(B5 SubNote)

SubNote on Solaris2.6 for x86 (MebiusNote-PJ)
Mobile-2 (AL-N1T513J5), Mobile-1 (TP230Cs)
New Home Office (P6-233 ATX), Home Office (P5-200 AT)

Base Components
SHARP Mebius NotePJ B5 1.37kg(PC-PJ1) (78Kb-JPEG image)
RipairCounter
kernel-2.2.1, apm-1.2, pcmcia-cs-3.0.8, eh097liJ(in 2.0.30)
BIOS Setting

CPU
MMX Pentium 233MHz(Tillamook) , PB-SRAM 256KByte
458.75 BogoMIPS(in kernel-2.0.36)
Memory
Memory: 63376k/65536k available (608k kernel code, 384k reserved, 1168k data)
EDO 64MegaByte (unchanged)
2.5" 9.5mm 6.4GigaByte Hard Disk Drive (Now Optional)
LILO-param: none
hda: IBM-DBCA-206480, 6194MB w/420kB Cache, CHS=789/255/63, (U)DMA ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Partition check:
hda: hda1 hda2 hda3 hda4
# /usr/sbin/hdparm -d1 -X34 -c1 -m16 /dev/hda [Enter]
# hdparm -i /dev/hda [Enter]
/dev/hda:
Model=IBM-DBCA-206480, FwRev=BC4OA8AF, SerialNo=HR2HRB01
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=13424/15/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=3(DualPortCache), BuffSize=420kB, MaxMultSect=16, MultSect=16
DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=2(fast)
CurCHS=789/255/63, CurSects=12685680, LBA=yes, LBAsects=12685680
tDMA={min:120,rec:120}, DMA modes: sword0 sword1 sword2 mword0 mword1 *mword2
IORDY=on/off, tPIO={min:240,w/IORDY:120}, PIO modes: mode3 mode4
# hdparm -v /dev/hda [Enter]
/dev/hda:
multcount = 16 (on)
I/O support = 1 (32-bit)
unmaskirq = 0 (off)
using_dma = 1 (off)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 789/255/63, sectors = 12685680, start = 0
2.5" 9.5mm 3.2GigaByte Hard Disk Drive (Original Compornent)
LILO-param: none
hda: HITACHI_DK237A-32, 3102MB w/512kB Cache, CHS=788/128/63, DMA ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Partition check:
hda: hda1 hda2 hda3 hda4
# /usr/sbin/hdparm -d1 -X34 -c1 -m16 /dev/hda [Enter]
# hdparm -i /dev/hda [Enter]
/dev/hda:
Model=HITACHI_DK237A-32, FwRev=00U0A0A0, SerialNo=127131
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=6304/16/63, TrkSize=36477, SectSize=579, ECCbytes=4
BuffType=3(DualPortCache), BuffSize=512kB, MaxMultSect=16, MultSect=16
DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=2(fast)
CurCHS=6304/16/63, CurSects=6354432, LBA=yes, LBAsects=6354432
tDMA={min:120,rec:120}, DMA modes: sword0 sword1 sword2 mword0 mword1 *mword2
IORDY=yes, tPIO={min:400,w/IORDY:120}, PIO modes: mode3 mode4
# hdparm -v /dev/hda [Enter]
/dev/hda:
multcount = 16 (on)
I/O support = 1 (32-bit)
unmaskirq = 0 (off)
using_dma = 1 (off)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 788/128/63, sectors = 6354432, start = 0
Video Chip
NeoMagic MagicGraph128ZV+ VRAM 1024KByte (128bit accelerater NM2097 Int.)
supported for XFree86-3.3.3 (/etc/XF86Config & xaabenchmark)
other driver Js Neomagic X Server for Linux on Laptops (customized XFree86-3.3.2) SVGA Server (/etc/XF86Config sample)
TFT Display
Netscape (murikuri-ja)
view 4.03-image(122kb)
800x600 256Color (-8bpp: 2009.8rpm),
800x600 65536Color (-16bpp: 960.9rpm),
for NonAcceralated Neomagic X SVGA Server

Pointing Device
Flat Pad (Tapping & Cyariblation result)
XF86Config: Protocol "ps/2", Device "/dev/psaux"
Sound
CRYSTAL CS-4237B (SoundBraster Pro compatible) Card config:
CS4232 at 0x530 irq 5 drq 1,3
(CS4232 MIDI at 0x300 irq 9 drq 0)
OPL-2/OPL-3 FM at 0x388 drq 0

PortReplicated Floppy Disk Drive (External.)
3.5" 3-Mode FDD, Assenbled Printer, RS-232C, PS/2connector
execute DE620 Pocket Ether Adaptor
EasyHard SCSI Host Adapter (for Bidirectional Pararell port)
RS-232C JumperBOX + Machintosh SCSI Cable, lp2 at 0x0278
Anfenor 50pin Half pitch Cable (kernel-2.0.30 for eh097liJ)
DataScope for DoCoMo on PCMCIA Celluer Modem Card
tty01 at 0x02f8 (irq = 3) is a 8250
tty06 at 0x01b0 (irq = 3) is a 8250
DataScope for DoCoMo(Analog19.2K Celluler Modem/FAX)
RS-232C PHS Data Communication Adapter
SII PHS DATA W32S(MC-6630) Alfa-DATA32
Connect to Victor TN-PZ5 on DDI-Pocket Alfa-DATA32(PIAFS, ISDN64K, Analog14.4K Modem/FAX)
PCMCIA PHS Data Communication Card
tty02 at 0x03e8 (irq = 3) is a 16550A
SII PHS DATA 32S(MC-6530) to Victor TN-PZ5 on DDI-Pocket Alfa-DATA32(PIAFS, ISDN64K, Analog14.4K Modem/FAX)
PCMCIA ISDN Adaptor
tty02 at 0x03e8 (irq = 10) is a 16450
TDK DN1280 I-interface chanel-B: AutoPPP, AutoMP, ITU-T V.110 38.4Kbps, 64Kbps, Bulk 128Kbps & chanel-D: ITU-T X.25 packet.
PCMCIA Data/FAX Modem
tty02 at 0x02f8 (irq = 10) is a 16550A
Megaherts XJ-3288J 33,600bps V.34 (XJ-4336J After UpGrade), connect to AtermIT35 analog Port
PCMCIA LAN+33.6k Fax/Modem Card
eth0: 3Com 3c562, port 0x300, irq 9, Auto port, hw_addr 00:60:97:XX:XX:XX
tty02 at 0x03e8 (irq = 9) is a 16550A (PPP DialUp connection 115,200bps)
3Com EtherLink-III LAN+33.6 Modem PC Cards 3C563C-TP
PCMCIA LAN Card-2
eth0: 3Com 3c589, port 0x300, irq 3, Auto port, hw_addr 00:A0:24:XX:XX:XX
eth0: autodetected 10baseT
3Com EtherLink-III Lan PC Cards 3C589C-TP
PCMCIA LAN Card-3
eth0: SMC91c92 at port 0x200, irq 9, 10baseT port, 00:00:86:XX:XX:XX.
Megaherts PCMCIA ETHERNET LAN Adapter XJ10BT(2)
PCMCIA Video Capture
IBM Smart Capture Card + ClipON Camera + TV-tunerOption
SCCdriver-0.33, xfscc-0.41 (in pcmcia-cs-2.9.11)
PCMCIA SCSI I/F Card -1
Adaptec APA-1460 Slim SCSI
Anfenor 50pin (Full & Half pitch) Cable
PCMCIA SCSI I/F Card -2
Qlogic Fast!SCSI
Anfenor 50pin Full pitch Cable
PD/CD-ROMx4 Drive (External.)
'TORAY'PhaseWriter TD-6010 PD:165ms 1141KB/sec, 4xCD-ROM:195ms 600KB/sec
connect to APA-1460 SlimSCSI
CD-ROM Drive (External.)
TOSHIBA XM4101B SCSI-2 x2
connect to EasyHard & APA-1460 Slim SCSI
ISDN Terminal Adapter-1 (External.)
NTT-TEyokyo MN128V21 128kMP(AutoMP, AutoBACP), Bandwidth on Demand, FAX1300Hz
connect to NTT-DSU for NTT INS-net64
ISDN Terminal Adapter-2 (External.)
NEC AtermIT35 Synchro(64Kbyte) un-Synchro(57.6Kbyte)
connect to NTT-DSU for NTT INS-net64

備考:
 kernel-2.2.1 にしてみました。が、module類の動作がいまいちです。('99.1.30)
 1998年末頃 内蔵2.5"HDD を IBM製 9.5" 6.4GByte に換装しました。
MebiusNotePJのHDD交換の際には、タッチ・パッドと組み合わされている為、 タッチ・パッドのコネクタ類(2ヶ所)の取扱いに注意します。
思った程難しい作業ではありませんでした。
 これで、Oracle-8.0.5を持ち歩けるようになりました...(^^)v('98.12.20)
 DataScope for DoCoMo を利用するには、/etc/pcmcia/config (in pcmcia-cs-3.0.4) に
  card "DataScope for DoCoMo on Celluer Modem"
   version "DataScope for DoCoMo", "1.00"
   bind "serial_cs"
というエントリを追加します。('98.08.02)
 MebiusNotePJで一番の問題は pcmcia-cs がそのままではうまく稼働しない事です。(pcmcia-cs-3.0.5以降では問題ありません...:-)
  [linux-users:31698] Re:
  From: IKEYAMA Tomonori
  To: linux-users@linux.or.jp
  Date: Sat, 25 Jul 1998 17:00:10 +0900
を参考になされると嬉しいかも知れません。
 私は"宴会ML"で、安達@WalkingLinuxさんのアドバイスに依り稼働できました。
  /usr/src/pcmcia-cs-3.0.4/modules/rl5c466.h の 26行目辺りの記述
    #ifndef PCI_DEVICE_ID_RICOH_RL5C466
    #define PCI_DEVICE_ID_RICOH_RL5C466 0x0466
    #endif
  を
    /* #ifndef PCI_DEVICE_ID_RICOH_RL5C466 */
    #define PCI_DEVICE_ID_RICOH_RL5C466 0x0475
    /* #endif */
  に変更してから pcmcia-cs-3.0.4 を CardBus: YES で構築します。

10/100BASE-TX カードに付いてですが、3Com 3c575-TX (32bit CardBus Card) は 問題なく利用できています。
何故か 16bit None CardBus Card の 3Com 3c574-TX のほうは、Let's Note での 状況と同様 eth0 インタフェースはできるものの Rx: Tx: パケットが飛んでくれませんでした...それ以外の 10Base Cardは問題なく稼働可能です。('98.08.02)
 pcmcia-cs がうまく稼働しないときのネットワークへの接続には、DE620ドライバで 稼働する PLANET製 EN-EPP-2T を外付けFDD背面のパラレルポートに接続しましょう。
SHARP メビウスノートPJ(PC-PJ1)へのLinuxインストールには『PLAMO』という 新しいしかもノートに優しい日本語ディストリビューションを使用しました。
 付属のXFree86-3.3.2のXF86Setupは日本語化されており一応NeoMagicも選択できます が、設定されるのはVGA16です。
しかし、Jeff Shoeyさん のNeomagic X Server for Linux on Laptopsを利用すれば、非アクセラレート版ですが、 16bpp の SVGA が利用可能です。
メビウスノートPJの11.3インチTFTとNeoMagic製MagicGraph128ZV+(NM2097)は、アクセラレーションなしでも十分高速で美しく快適に動作しています。('98-07-05)


 ◆ Portable LiNUX World 'The Hardware' Buyers Guide

Portable LiNUX World Home Page← Portable LiNUX World Home Page


Mail to: egota@linet.gr.jp