VSPE

WiSP virtual connection to MixW with VSPE #2

by ST2NH and JE9PEL


I changed a policy to 'Pair type' from 'Connector type' of VSPE device.

COM2 ... PTT serial port
COM4 ... MixW virtual port
COM5 ... WiSP virtual port

Device Pair type
VSPE setup







MixW setup





WiSP setup




PTT port supplement

Subject: WiSP virtual connection to MixW with VSPE
From: Mineo Wakita, JE9PEL
To: Nader Omer, ST2NH
Date: Monday, February 15, 2010, 2:56 AM

I had setup VSPE, MixW, and WiSP.
I use usually an external soundcard on COM2.
So I had setup the virtual serial port of VSPE in COM4.

When I request 'Fill Directory' on WiSP(MSPE), I can hear
the sound of that request in my PC and I can see some messeges
in MixW. But my rig does not do the uplink work. Why?

------------------------------------------------------------------------

Re: WiSP virtual connection to MixW with VSPE
From: Nader Omer
To: Mineo Wakita
Date: Mon, 15 Feb 2010 05:08:08 -0800 (PST)

It is look like you have some problem in MixW keying port!!

keying setup as following:-
 
Configuer --> TRCVR CAT/PTT --> CAT NONE --> PTT&CAT INTERFACE
 --> (SELECT HERE YOUR KEY COM)

Notice Cat is disabled and all other com port at mixw were
disabled except emulator kiss port for VSPE and PTT port.

Tx and Rx audio direct from radio data socket to soundcards.

------------------------------------------------------------------------

Subject: WiSP(MSPE) RX?
From: Mineo Wakita
To: Nader Omer
Date: Wednesday, February 17, 2010, 3:57 AM

Hello Nader,

I think that all the settings of VSPE, MixW, and WiSP(MSPE) are right.

MSPE receive the signal from MixW just only after MSPE started, and
MSPE bigin to uplink a message to the satellite once.

After this, the signal are receiving on a MixW window, but the signal
are not passed to MSPE from MixW at all. In other words, nothing is
displayed on MSPE window after this. Do you understand why is it?

------------------------------------------------------------------------

Re: WiSP(MSPE) RX?
From: Nader Omer
To: Mineo Wakita
Date: Wed, 17 Feb 2010 04:47:24 -0800 (PST)

Hi Mineo Good day/nigth

Looks like com conflict!

Ok do this steps it may help

Start VSPE 1st
Start MIXW 2nd
Finely Wisp and MSPE

MIXW is so sensitive to shut down the kiss port even if not market with
disable marked!

I use to restart the software in the same above mentioned sequence when
ever I did any changes or when I feel there is something wrong.

I notice sometime VSPE got a good memory for any conflict so restart it
may help. I use to save the configuration of com connector in VSPE and
reopen when restart More fast than to rebuild the connection again.

Changing the com in VSPE many help too

Check and disable MIXW multi port serial adapters if it has been
installed in your PC.

Also checking soundcard audio level it may help but
I don't think there is a problem at least on 1k2 baud rate with HO-68
The most difficult part is the audio over load  I noticed from the data
socket to soundcard Input ! I solved by direct audio output from rig's
audio socket.

Play with the same setting on other PC I did so and on every pc there
weresomething deferent.

Hope this wll helps my friend

------------------------------------------------------------------------

Subject: VSPE device pair type
From: Mineo Wakita
To: Nader Omer
Date: Wednesday, February 17, 2010, 9:03 AM

I changed a policy to 'Pair type' from 'Connector type' of VSPE device.

COM2 ... PTT serial port
COM4 ... MixW virtual port
COM5 ... WiSP virtual port

------------------------------------------------------------------------

COM port change plan

COM 1, USB Serial Converter ... TNC, SRLL etc. main com port
COM 2, USB Serial Port      ... UISS etc. PTT, external sound card port
COM 3, Soft Modem AMR       ... PC internal modem
COM 4, USB Serial Port      ... relative COM2 (changed to COM2 from COM4)
COM 5, USB Serial Converter ... relative COM1 (changed to COM1 from COM5)
COM 6, FOMA N-05A           ... NTT Docomo connection manager
COM 7, MixW serial port     ... bridge #2 input
COM 8, MixW serial port     ... bridge #2 output
COM 9, USB-to-Serial port   ... HRD com port
COM10, MixW serial port     ... bridge #1 input
COM11, MixW serial port     ... bridge #1 output

I'm going to be disable from COM 7 to COM 11 of 'MixW serial port bridge',
and setup COM 7 for 'VSPE virtual device type Connector' together with
MixW and WiSP(MSPE).



SUDT AccessPort

------------------------------------------------------------------------

[Supplement]

com0com
http://sourceforge.net/projects/com0com/

KySat-2 decoder via virtual ports
http://st2nh-blogger.blogspot.jp/2013/12/kysat-2-decoder-via-virtual-ports.html